InGaN Platelets: Synthesis and Applications toward Green and Red Light-Emitting Diodes.

In this work, we present a method to synthesize arrays of hexagonal InGaN submicrometer platelets with a top c-plane area having an extension of a few hundred nanometers by selective area metal-organic vapor-phase epitaxy. The InGaN platelets were made by in situ annealing of InGaN pyramids, whereby InGaN from the pyramid apex was thermally etched away, leaving a c-plane surface, while the inclined {101̅1} planes of the pyramids were intact. The as-formed c-planes, which are rough with islands of a few tens of nanometers, can be flattened with InGaN regrowth, showing single bilayer steps and high-quality optical properties (full width at half-maximum of photoluminescence at room temperature: 107 meV for In0.09Ga0.91N and 151 meV for In0.18Ga0.82N). Such platelets offer surfaces having relaxed lattice constants, thus enabling shifting the quantum well emission from blue (as when grown on GaN) to green and red. For single InGaN quantum wells grown on the c-plane of such InGaN platelets, a sharp interface between the quantum well and the barriers was observed. The emission energy from the quantum well, grown under the same conditions, was shifted from 2.17 eV on In0.09Ga0.91N platelets to 1.95 eV on In0.18Ga0.82N platelets as a result of a thicker quantum well and a reduced indium pulling effect on In0.18Ga0.82N platelets. On the basis of this method, prototype light-emitting diodes were demonstrated with green emission on In0.09Ga0.91N platelets and red emission on In0.18Ga0.82N platelets.

Optimization of Current Injection in AlGaInP Core-Shell Nanowire Light-Emitting Diodes.

Core-shell nanowires offer great potential to enhance the efficiency of light-emitting diodes (LEDs) and expand the attainable wavelength range of LEDs over the whole visible spectrum. Additionally, nanowire (NW) LEDs can offer both improved light extraction and emission enhancement if the diameter of the wires is not larger than half the emission wavelength (λ/2). However, AlGaInP nanowire LEDs have so far failed to match the high efficiencies of traditional planar technologies, and the parameters limiting the efficiency remain unidentified. In this work, we show by experimental and theoretical studies that the small nanowire dimensions required for efficient light extraction and emission enhancement facilitate significant loss currents, which result in a low efficiency in radial NW LEDs in particular. To this end, we fabricate AlGaInP core-shell nanowire LEDs where the nanowire diameter is roughly equal to λ/2, and we find that both a large loss current and a large contact resistance are present in the samples. To investigate the significant loss current observed in the experiments in more detail, we carry out device simulations accounting for the full 3D nanowire geometry. According to the simulations, the low efficiency of radial AlGaInP nanowire LEDs can be explained by a substantial hole leakage to the outer barrier layer due to the small layer thicknesses and the close proximity of the shell contact. Using further simulations, we propose modifications to the epitaxial structure to eliminate such leakage currents and to increase the efficiency to near unity without sacrificing the λ/2 upper limit of the nanowire diameter. To gain a better insight of the device physics, we introduce an optical output measurement technique to estimate an ideality factor that is only dependent on the quasi-Fermi level separation in the LED. The results show ideality factors in the range of 1-2 around the maximum LED efficiency even in the presence of a very large voltage loss, indicating that the technique is especially attractive for measuring nanowire LEDs at an early stage of development before electrical contacts have been optimized. The presented results and characterization techniques form a basis of how to simultaneously optimize the electrical and optical efficiency of core-shell nanowire LEDs, paving the way to nanowire light emitters that make true use of larger-than-unity Purcell factors and the consequently enhanced spontaneous emission.

Simplifying Nanowire Hall Effect Characterization by Using a Three-Probe Device Design.

Electrical characterization of nanowires is a time-consuming and challenging task due to the complexity of single nanowire device fabrication and the difficulty in interpreting the measurements. We present a method to measure Hall effect in nanowires using a three-probe device that is simpler to fabricate than previous four-probe nanowire Hall devices and allows characterization of nanowires with smaller diameter. Extraction of charge carrier concentration from the three-probe measurements using an analytical model is discussed and compared to simulations. The validity of the method is experimentally verified by a comparison between results obtained with the three-probe method and results obtained using four-probe nanowire Hall measurements. In addition, a nanowire with a diameter of only 65 nm is characterized to demonstrate the capabilities of the method. The three-probe Hall effect method offers a relatively fast and simple, yet accurate way to quantify the charge carrier concentration in nanowires and has the potential to become a standard characterization technique for nanowires.

Designed Quasi-1D Potential Structures Realized in Compositionally Graded InAs1-xPx Nanowires.

III-V semiconductor heterostructures are important components of many solid-state optoelectronic devices, but the ability to control and tune the electrical and optical properties of these structures in conventional device geometries is fundamentally limited by the bulk dimensionality and the inability to accommodate lattice-mismatched material combinations. Here we demonstrate how semiconductor nanowires may enable the creation of arbitrarily shaped one-dimensional potential structures for new types of designed device functionality. We describe the controlled growth of stepwise compositionally graded InAs1-xPx heterostructures defined along the axes of InAs nanowires, and we show that nanowires with sawtooth-shaped composition profiles behave as near-ideal unipolar diodes with ratchet-like rectification of the electron transport through the nanowires, in excellent agreement with simulations. This new type of designed quasi-1D potential structure represents a significant advance in band gap engineering and may enable fundamental studies of low-dimensional hot-carrier dynamics, in addition to constituting a platform for implementing novel electronic and optoelectronic device concepts.

Comparing Hall Effect and Field Effect Measurements on the Same Single Nanowire.

We compare and discuss the two most commonly used electrical characterization techniques for nanowires (NWs). In a novel single-NW device, we combine Hall effect and back-gated and top-gated field effect measurements and quantify the carrier concentrations in a series of sulfur-doped InP NWs. The carrier concentrations from Hall effect and field effect measurements are found to correlate well when using the analysis methods described in this work. This shows that NWs can be accurately characterized with available electrical methods, an important result toward better understanding of semiconductor NW doping.

Radial Nanowire Light-Emitting Diodes in the (AlxGa1-x)yIn1-yP Material System.

Nanowires have the potential to play an important role for next-generation light-emitting diodes. In this work, we present a growth scheme for radial nanowire quantum-well structures in the AlGaInP material system using a GaInP nanowire core as a template for radial growth with GaInP as the active layer for emission and AlGaInP as charge carrier barriers. The different layers were analyzed by X-ray diffraction to ensure lattice-matched radial structures. Furthermore, we evaluated the material composition and heterojunction interface sharpness by scanning transmission electron microscopy energy dispersive X-ray spectroscopy. The electro-optical properties were investigated by injection luminescence measurements. The presented results can be a valuable track toward radial nanowire light-emitting diodes in the AlGaInP material system in the red/orange/yellow color spectrum.

A comparative study of absorption in vertically and laterally oriented InP core-shell nanowire photovoltaic devices.

We have compared the absorption in InP core-shell nanowire p-i-n junctions in lateral and vertical orientation. Arrays of vertical core-shell nanowires with 400 nm pitch and 280 nm diameter, as well as corresponding lateral single core-shell nanowires, were configured as photovoltaic devices. The photovoltaic characteristics of the samples, measured under 1 sun illumination, showed a higher absorption in lateral single nanowires compared to that in individual vertical nanowires, arranged in arrays with 400 nm pitch. Electromagnetic modeling of the structures confirmed the experimental observations and showed that the absorption in a vertical nanowire in an array depends strongly on the array pitch. The modeling demonstrated that, depending on the array pitch, absorption in a vertical nanowire can be lower or higher than that in a lateral nanowire with equal absorption predicted at a pitch of 510 nm for our nanowire geometry. The technology described in this Letter facilitates quantitative comparison of absorption in laterally and vertically oriented core-shell nanowire p-i-n junctions and can aid in the design, optimization, and performance evaluation of nanowire-based core-shell photovoltaic devices.

Study of carrier concentration in single InP nanowires by luminescence and Hall measurements.

The free electron carrier concentrations in single InP core-shell nanowires are determined by micro-photoluminescence, cathodoluminescence (CL) and Hall effect measurements. The results from luminescence measurements were obtained by solving the Fermi-Dirac integral, as well as by analyzing the peak full width at half maximum (FWHM). Furthermore, the platform used for Hall effect measurements, combined with spot mode CL spectroscopy, is used to determine the carrier concentrations at specific positions along single nanowires. The results obtained via luminescence measurements provide an accurate and rapid feedback technique for the epitaxial development of doping incorporation in nanowires. The technique has been employed on several series of samples in which growth parameters, such as V/III-ratio, temperature and dopant flows, were investigated in an optimization procedure. The correlation between the Hall effect and luminescence measurements for extracting the carrier concentration of different samples were in excellent agreement.

Crystal phase-dependent nanophotonic resonances in InAs nanowire arrays.

Nanostructures have many material, electronic, and optical properties that are not found in bulk systems and that are relevant for technological applications. For example, nanowires realized from III-V semiconductors can be grown into a wurtzite crystal structure. This crystal structure does not naturally exist in bulk where these materials form the zinc-blende counterpart. Being able to concomitantly grow these nanowires in the zinc-blende and/or wurtzite crystal structure provides an important degree of control for the design and optimization of optoelectronic applications based on these semiconductor nanostructures. However, the refractive indices of this new crystallographic phase have so far not been elucidated. This shortcoming makes it impossible to predict and utilize the full potential of these new nanostructured materials for optoelectronics applications: a careful design and optimization of optical resonances by tuning the nanostructure geometry is needed to achieve optimal performance. Here, we report and analyze striking differences in the optical response of nanophotonic resonances in wurtzite and zinc-blende InAs nanowire arrays. Specifically, through reflectance measurements we find that the resonance can be tuned down to λ ≈ 380 nm in wurtzite nanowires by decreasing the nanowire diameter. In stark contrast, a similar tuning to below λ ≈ 500 nm is not possible in the zinc-blende nanowires. Furthermore, we find that the wurtzite nanowires can absorb twice as strongly as the zinc-blende nanowires. We attribute these strikingly large differences in resonant behavior to large differences between the refractive indices of the two crystallographic phases realized in these nanostructures. We anticipate our findings to be relevant for other III-V materials as well as for all material systems that manifest polytypism. Taken together, our results demonstrate crystal phase engineering as a potentially new design dimension for optoelectronics applications.

Synthesis of doped InP core-shell nanowires evaluated using hall effect measurements.

InP core-shell nanowire pn-junctions doped with Zn and Sn have been investigated in terms of growth morphology and shell carrier concentration. The carrier concentrations were evaluated using spatially resolved Hall effect measurements and show improved homogeneity compared to previous investigations, attributed to the use of Sn as the n-type dopant. Anisotropies in the growth rate of different facets are found for different doping levels that in turn affects the migration of Sn and In on the nanowire surface. A route for increasing the In migration length to obtain a more homogeneous shell thickness is presented.

Electron-beam patterning of polymer electrolyte films to make multiple nanoscale gates for nanowire transistors.

We report an electron-beam based method for the nanoscale patterning of the poly(ethylene oxide)/LiClO4 polymer electrolyte. We use the patterned polymer electrolyte as a high capacitance gate dielectric in single nanowire transistors and obtain subthreshold swings comparable to conventional metal/oxide wrap-gated nanowire transistors. Patterning eliminates gate/contact overlap, which reduces parasitic effects and enables multiple, independently controllable gates. The method's simplicity broadens the scope for using polymer electrolyte gating in studies of nanowires and other nanoscale devices.

Conductance enhancement of InAs/InP heterostructure nanowires by surface functionalization with oligo(phenylene vinylene)s.

We have investigated the electronic transport through 3 µm long, 45 nm diameter InAs nanowires comprising a 5 nm long InP segment as electronic barrier. After assembly of 12 nm long oligo(phenylene vinylene) derivative molecules onto these InAs/InP nanowires, we observed a pronounced, nonlinear I-V characteristic with significantly increased currents of up to 1 µA at 1 V bias, for a back-gate voltage of 3 V. As supported by our model calculations based on a nonequilibrium Green Function approach, we attribute this effect to charge transport through those surface-bound molecules, which electrically bridge both InAs regions across the embedded InP barrier.

Spatially resolved Hall effect measurement in a single semiconductor nanowire.

Efficient light-emitting diodes and photovoltaic energy-harvesting devices are expected to play an important role in the continued efforts towards sustainable global power consumption. Semiconductor nanowires are promising candidates as the active components of both light-emitting diodes and photovoltaic cells, primarily due to the added freedom in device design offered by the nanowire geometry. However, for nanowire-based components to move past the proof-of-concept stage and be implemented in production-grade devices, it is necessary to precisely quantify and control fundamental material properties such as doping and carrier mobility. Unfortunately, the nanoscale geometry that makes nanowires interesting for applications also makes them inherently difficult to characterize. Here, we report a method to carry out Hall measurements on single core-shell nanowires. Our technique allows spatially resolved and quantitative determination of the carrier concentration and mobility of the nanowire shell. As Hall measurements have previously been completely unavailable for nanowires, the experimental platform presented here should facilitate the implementation of nanowires in advanced practical devices.

A cathodoluminescence study of the influence of the seed particle preparation method on the optical properties of GaAs nanowires.

Cathodoluminescence at 8 K is used to compare the optical properties of AlGaAs-capped GaAs nanowires, grown by metal-organic vapour phase epitaxy and seeded by gold particles prepared by different methods. Six different methods were used to fabricate and deposit gold seed particles onto GaAs substrates: colloid particles, aerosol particles and particles defined by electron beam lithography. The nanowires were grown with and without an in situ annealing step prior to the nanowire growth. The morphology showed no significant differences between the nanowires. The emissions from ensembles of nanowires have the same peak position, irrespective of seed particle type. Without the in situ annealing step prior to the nanowire growth, there are significant differences in the emission intensity and emission patterns from nanowires grown from different seed particles. When an in situ annealing step is included, all the resulting nanowires show identical optical emission intensity and emission patterns. This shows the importance of using an in situ annealing step prior to growth. This study demonstrates that different preparation methods for gold seed particles can be used to produce GaAs nanowires with highly similar optical properties. The choice of particle preparation method to be used can therefore be based on availability and cost.

Electrical and optical properties of InP nanowire ensemble p⁺-i-n⁺ photodetectors.

We report on a comprehensive study of electrical and optical properties of efficient near-infrared p⁺-i-n⁺ photodetectors based on large ensembles of self-assembled, vertically aligned i-n⁺ InP nanowires monolithically grown on a common p⁺ InP substrate without any buffer layer. The nanowires have a polytype modulated crystal structure of wurtzite and zinc blende. The electrical data display excellent rectifying behavior with an ideality factor of about 2.5 at 300 K. The ideality factor scales with 1/T, which possibly reflects deviations from classical transport models due to the mixed crystal phase of the nanowires. The observed dark leakage current is of the order of merely ∼100 fA/nanowire at 1 V reverse bias. The detectors display a linear increase of the photocurrent with reverse bias up to about 10 pA/nanowire at 5 V. From spectrally resolved measurements, we conclude that the photocurrent is primarily generated by funneling photogenerated carriers from the substrate into the NWs. Contributions from direct excitation of the NWs become increasingly important at low temperatures. The photocurrent decreases with temperature with an activation energy of about 50 meV, which we discuss in terms of a temperature-dependent diffusion length in the substrate and perturbed transport through the mixed-phase nanowires.

Realizing lateral wrap-gated nanowire FETs: controlling gate length with chemistry rather than lithography.

An important consideration in miniaturizing transistors is maximizing the coupling between the gate and the semiconductor channel. A nanowire with a coaxial metal gate provides optimal gate-channel coupling but has only been realized for vertically oriented nanowire transistors. We report a method for producing laterally oriented wrap-gated nanowire field-effect transistors that provides exquisite control over the gate length via a single wet etch step, eliminating the need for additional lithography beyond that required to define the source/drain contacts and gate lead. It allows the contacts and nanowire segments extending beyond the wrap-gate to be controlled independently by biasing the doped substrate, significantly improving the subthreshold electrical characteristics. Our devices provide stronger, more symmetric gating of the nanowire, operate at temperatures between 300 and 4 K, and offer new opportunities in applications ranging from studies of one-dimensional quantum transport through to chemical and biological sensing.

Scanning gate imaging of quantum dots in 1D ultra-thin InAs/InP nanowires.

We use a scanning gate microscope (SGM) to characterize one-dimensional ultra-thin (diameter ≈ 30 nm) InAs/InP heterostructure nanowires containing a nominally 300 nm long InAs quantum dot defined by two InP tunnel barriers. Measurements of Coulomb blockade conductance versus backgate voltage with no tip present are difficult to decipher. Using the SGM tip as a charged movable gate, we are able to identify three quantum dots along the nanowire: the grown-in quantum dot and an additional quantum dot near each metal lead. The SGM conductance images are used to disentangle information about individual quantum dots and then to characterize each quantum dot using spatially resolved energy-level spectroscopy.

Gate-induced fermi level tuning in InP nanowires at efficiency close to the thermal limit.

As downscaling of semiconductor devices continues, one or a few randomly placed dopants may dominate the characteristics. Furthermore, due to the large surface-to-volume ratio of one-dimensional devices, the position of the Fermi level is often determined primarily by surface pinning, regardless of doping level. In this work, we investigate the possibility of tuning the Fermi level dynamically with wrap-around gates, instead of statically setting it using the impurity concentration. This is done using Ω-gated metal-oxide-semiconductor field-effect transistors with HfO(2)-capped InP nanowires as channel material. It is found that induced n-type devices exhibit an optimal inverse subthreshold slope of 68 mV/decade. By adjusting the growth and process parameters, it is possible to produce ambipolar devices, in which the Fermi level can be tuned across the entire band gap, making it possible to induce both n-type and p-type conduction.